Waffle Weave Towel idea

My Waffle Weave, up close.

So I thought, ok I have done a few classes and a couple projects on my own now, its time to step up my game a little.  This project all I had to start with was - I want to make some dish towels with this 8/2 yarn I already have.  Its a lot harder than you think.  I had no pattern, no book telling me what sett I need, no idea how much yarn length I need, had to try to work it all out.  I decided I liked the look of waffle weave, which I had seen but had not found any patterns for.  I searched my green book of patterns (the old one) and there was one page of waffle weave, so I picked one and started there.  I figure I want to make these towels about 12x18 inches, with a little hem, no fringe.  In searching for a blank template to calculate how much yarn I need, I found this great pdf file Warp Calculation Worksheet which really helped a lot.  For the first project I am just going to make two towels.  That way its quick gratification, and if this weight of yarn and pattern works out, then I can always repeat it because I have everything written down.  Since my warping board is a yard wide I decided to round up to 2.5 yards for the length of the warp.  I also have to remember to write down what the finished size is before and after washing, to find out the shrinkage, I had to guess.


Day 1
282 threads measured on my warping board, sorry forgot to take a photo of this.

Day 2
 Today I took the threads and put them in the reed and then took the reed to the loom.  Doesnt sound like much but it does take a while

Day 3
Today I concentrated on warping on.  After watching the Interweave warping video, I have decided I really like the front to back method best.  Here I am putting each thread through the necessary heddle.  This also takes a while to do.  Its amazing that it takes a few days just to set up the loom.

 All tied on!  Ready to weave tomorrow.  This picture gives a good indication of the base color of the towel.

Day 4
Got started weaving today.  Had a little set back, two threads were crossed, which actually messes up about 4 threads in total.  Glad I caught it during the first half inch which is waste anyway.  Took half an hour to straighten out.  But here is what its going to look like.

 Close up of the weave, best I could get, it doesnt show the variegated colors well.  I think that even though my goal was to have the variegated be dominant that its the rust that will be.

Day 5-end
The days are pretty much the same from here to the end.  I work a little at a time as time permits.  This time, once I was done with the two towels, I decided to cut them off the loom in front so that I can try a technique I have heard about where I can tie on new warp without having to rethread it.  I have to just decide now if I want to make another two towels (I have enough of this same thread to do that) or do I want to change the colors?  Here is what it looks like off loom.  I have to now wash them up and see what kind of shrinkage I get. 

Batch 2 tied on, 5/30
I decided to try tying on from the original threading, but this time am using the variegated for the warp, just to see if it looks any different.  I had a couple of threads break mid tightening, but for the most part, this seems like an easier way than rethreading the heddles again.  I have to say though, because I am doing 2 more towels, of the same I just did, its lost some of its excitement.  I want to get these done so I can move on to the Ontario project. (will start a new post for that project)  I did not realize how very long it would take to make towels, and I need to make, whew lets see, at least a dozen. 

Nell's Easter Basket

Starting the bottom of the basket

 Half way up the side

 Got distracted and didnt take any more pictures :)

all done, 6 inch little Easter Basket for Nell

Aurora Borealis - A Guild Project

I belong to a guild called Weaving Indiana.  The guild is creating an exhibit for entry into the 2011 Midwest Weavers Conference Guild Exhibit competition. The theme for this exhibit is Aurora Borealis -- “Northern lights, ever changing, always in motion, a whisper of color and never the same.”

The guidelines are:

Exhibit scarf/shawl guidelines:
• all yarn used to be 8/2 Tencel
• any width scarf or shawl can be woven
• woven length must be 72” or longer
• fringe or hem as desired
• warp OR weft must be black tencel (purchased, not hand-dyed)
• additional color(s) should be any brilliant hue that can be seen in the northern lights, and can be hand-dyed if desired
• any weave structure can be used (consider using one that shows movement, like an advancing or undulating twill)
• colors inspired by a photo of the aurora borealis
• the weaver will provide the drawdown, fiber information and photo to be included in the display book

With these rules I decided I wanted to find a pattern that would not be too advanced or complex since I am a new weaver, but not a simple plain pattern either.  I wanted something that shows some movement. 
I sort of went at it backwards, I found what pattern I wanted to do first, then looked for a picture that reminded me of that pattern in the Aurora.  Here is the final picture that I found.

 So I had to get the fiber.  The warp is going to be a hand painted warp (no I didnt make this one, but its on my list of things to do in the future) and then weft will be the black tencel.  The colors do not really show well in my photo, so I will link the photo from Tabby Tree Weaver below my picture, where I purchased the warp.  Its a blue/purple/green. 

I then went through quite a few books, of which a few that I have contain hundreds of patterns and narrowed it down to a few, then finally chose one.  In the Handweaver's Pattern Directory I chose a 3/1 twill pattern that I liked.  It shows many variations and I chose the darker looking one on this page.

There were several others I considered, including some from another book that I have, but this one spoke to me and I decided to go with it.

So first step is to slay the reed with the painted warp.   Deciding sett is still very hard for me.  I want to try to make this about 8 or 10 inches wide.  (such interesting items on my kitchen table, hmm)

Day 1

I decided to use all the threads in the bundle, 246 total which will make the scarf just over 10 inches wide if I am calculating correctly.  I threaded my 12 dent reed with 2 threads per dent.  My plan is to use a double thread float on the edges.  The warp is 3 1/2 yards long.  This ends day 1.

Day 2

Today was a long day.  It was threading the heddles day.  It took me several hours, and I had 2 threads break so got to experience that too today.  This time I asked Michael to take some photos for me with my camera so I could be in them :)

I have taken the back beam off and am doing a front to back threading.

 Every single thread has to go through its own heddle.  Just getting started here.

 Got to the very end and realized I miscounted heddles on the third shaft, I was ONE short!  I had to take some off the first shaft and move them to the third one, and mid warp that is not easy or fun.

Finally got all the heddles threaded and am winding on.  This is the view from the top.
You can really see the colors here.  Painted warps are so very cool.  I must take the warp painting class so I can make one.

 Here is a view from the front, about half way done winding on.

And its finally all on the loom, weaving starts tomorrow.

Day 3
I got to work a total of 30 minutes on this tonight because of work.  Here is all I got done.

I thought about it a little while and going with the theme of the Aurora, thought to randomize my pattern a little.  Not sure how I will write that on the draft.

Day 4
Had more time this evening to work on it.  Started measuring how long the finished fabric is.  I finished tonight at 23 inches on loom.  I think it was like about 4-6 inches when I started.  Whew minimum is 72 inches and I have to make it longer to allow for shrinkage when I wash it.

Day 5

Did a lot today.  I added a light and tv tray to my set up.

 Here is a shot of the underside of the weaving.

 I got to about 54 inches today finished.

 Close up of the weaving

 Back of the loom, just because it showed some real neat colors.

Day 6
Unmotivated today, only sat and did weaving for about half an hour.
Day 7
Did about an hour on it today, do not see it being done before Saturday.  70 inches
Day 8
Did about an hour also today, another 15 inches

Day 9
Finished!  Total size 9.25 x 91.75 inches

First Weave on my new Loom

This is an adaptation of the Double Court Bob Minor pattern, page 50 of Sixty Scarves for 60 years.

I didnt have the 10/2 the pattern called for so I used some mill end yard that I had, which was 6/2 and I decided to try it in the 10 dent reed.  I am still a little unclear on taking a pattern that calls for one type of yarn and substituting a different size and how to change the sett.  I decided to not only try out my loom with this pattern but to try out modifying the pattern.  This pattern has a repeat of 16 threads in the threading so I wound 80 ends plus 2 for float which should be 5 repeats.  I decided to do a very short warp of just 2 yards.

Then I decided to try the warping technique in the video I borrowed from the Weaving Indiana Guild, Warping your Loom.  This is a front to back warping.  I sleyed the reed with it out of the loom sitting on the kitchen table then moved it to the loom

 Then from the back, I removed the rear beam so I could get to the heddles easier and threaded them then put the rear beam back on.  I then did the tie up of the treadles.

 And this is where I decided to stop for the evening.  I am going to edit this post each time I have an update to keep the project in one post heading.

Day 2, its going really quickly

 About 12 inches so far

 Now you can see a bunch on the front beam

 Close up of the fabric after taking it off the loom.  This one was just a small piece.

It's HERE!!!

Taking the Baby Wolf out of the shipping crate

 Added the strings to the loom

 Attached the handle.

 Put on all the heddles!  I got 800, but I didnt put them all on.

NOW, I am off to finish up a little bit of email and then plan and maybe warp up a short project!

Overshot Weaving Class day 2 of 2

Today was day 2 of the weaving class.  Sadly, I forgot my camera so could not show you any pictures of the work in progress.  But, I can show you my finished weaving.  The first part of the weaving shows 4 different treddlings.  Then I tried using a navy for the tabby for just a little bit, I didnt like that.  Then I tried to use red for the tabby, the pattern was lost.  Then I wove a large white section and finished the rest of the length with treddle pattern #4 which I liked the most.

 Here is a close up of the larger woven section

 This is the whole length folded over.